Problem at booting

Vivek Mangal vivek.mangal9685 at gmail.com
Fri Feb 15 04:06:22 UTC 2008


ok i understand why u say this.
But which card is 32 bits ?
how can i recognize that card ?
by which command i detect that card ?


On 2/14/08, Vivek Mangal <vivek.mangal9685 at gmail.com> wrote:
>
> But, Which card ?
> and how u can say that ?
> tell me
>
> On 2/13/08, Vivek Mangal <vivek.mangal9685 at gmail.com> wrote:
> >
> > The output of command  #lspci -vv  is
> > ----------------------------------------
> > pcilib: Resource 3 in /sys/bus/pci/devices/0000:00:00:0/resource has a
> > 64-bit address, ignoring
> > 00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a33 (rev 01)
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort+ >SERR- <PERR-
> >     Latency: 64
> >     Region 3: Memory at <ignored> (64-bit, non-prefetchable)
> >
> > 00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if
> > 00 [Normal decode])
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 99
> >     Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> >     I/O behind bridge: 0000e000-0000efff
> >     Memory behind bridge: fde00000-fdefffff
> >     Prefetchable memory behind bridge: f0000000-f7ffffff
> >     Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort+ <SERR- <PERR-
> >     BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> >     Capabilities: [b0] #0d [0000]
> >
> > 00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA
> > Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 08
> >     Interrupt: pin A routed to IRQ 169
> >     Region 0: I/O ports at ff00 [size=8]
> >     Region 1: I/O ports at fe00 [size=4]
> >     Region 2: I/O ports at fd00 [size=8]
> >     Region 3: I/O ports at fc00 [size=4]
> >     Region 4: I/O ports at fb00 [size=16]
> >     Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
> >     Expansion ROM at fdf80000 [disabled] [size=512K]
> >     Capabilities: [60] Power Management version 2
> >         Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> > PME(D0-,D1-,D2-,D3hot-,D3cold-)
> >         Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> >     Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA
> > Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 08
> >     Interrupt: pin A routed to IRQ 177
> >     Region 0: I/O ports at fa00 [size=8]
> >     Region 1: I/O ports at f900 [size=4]
> >     Region 2: I/O ports at f800 [size=8]
> >     Region 3: I/O ports at f700 [size=4]
> >     Region 4: I/O ports at f600 [size=16]
> >     Region 5: Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
> >     Expansion ROM at fdf80000 [disabled] [size=512K]
> >     Capabilities: [60] Power Management version 2
> >         Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> > PME(D0-,D1-,D2-,D3hot-,D3cold-)
> >         Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> >     Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host
> > Controller (rev 80) (prog-if 10 [OHCI])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 20
> >     Interrupt: pin A routed to IRQ 185
> >     Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
> >     Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host
> > Controller (rev 80) (prog-if 10 [OHCI])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 20
> >     Interrupt: pin A routed to IRQ 185
> >     Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
> >     Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
> > Controller (rev 80) (prog-if 20 [EHCI])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 20
> >     Interrupt: pin A routed to IRQ 185
> >     Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
> >     Capabilities: [dc] Power Management version 2
> >         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> > PME(D0+,D1+,D2+,D3hot+,D3cold-)
> >         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> >         Bridge: PM- B3+
> >     Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Region 0: I/O ports at 0b00 [size=16]
> >     Region 1: Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
> >
> > 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI
> > IDE Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64
> >     Interrupt: pin A routed to IRQ 193
> >     Region 0: I/O ports at <unassigned>
> >     Region 1: I/O ports at <unassigned>
> >     Region 2: I/O ports at <unassigned>
> >     Region 3: I/O ports at <unassigned>
> >     Region 4: I/O ports at f400 [size=16]
> >     Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 00:14.2 Class 0403: ATI Technologies Inc: Unknown device 437b (rev 01)
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64, Cache Line Size 08
> >     Interrupt: pin ? routed to IRQ 193
> >     Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
> >     Capabilities: [50] Power Management version 2
> >         Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> > PME(D0+,D1-,D2-,D3hot+,D3cold+)
> >         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> >     Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
> > Enable-
> >         Address: 0000000000000000  Data: 0000
> >
> > 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev
> > 80)
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 0
> >
> > 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev
> > 80) (prog-if 01 [Subtractive decode])
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64
> >     Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> >     I/O behind bridge: 0000d000-0000dfff
> >     Memory behind bridge: fdd00000-fddfffff
> >     Prefetchable memory behind bridge: fdc00000-fdcfffff
> >     Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort+ <SERR- <PERR-
> >     BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> >
> > 01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device
> > 5a61 (prog-if 00 [VGA])
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64 (2000ns min), Cache Line Size 08
> >     Interrupt: pin A routed to IRQ 201
> >     Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> >     Region 1: I/O ports at ee00 [size=256]
> >     Region 2: Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
> >     Capabilities: [50] Power Management version 2
> >         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> > PME(D0-,D1-,D2-,D3hot-,D3cold-)
> >         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> >     Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
> > Enable-
> >         Address: 00000000  Data: 0000
> >
> > 02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> > RTL-8139/8139C/8139C+ (rev 10)
> >     Subsystem: Intel Corporation: Unknown device d600
> >     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Latency: 64 (8000ns min, 16000ns max)
> >     Interrupt: pin A routed to IRQ 209
> >     Region 0: I/O ports at de00 [size=256]
> >     Region 1: Memory at fddff000 (32-bit, non-prefetchable) [size=256]
> >     Capabilities: [50] Power Management version 2
> >         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> > PME(D0-,D1+,D2+,D3hot+,D3cold+)
> >         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> >
> > 02:04.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09)
> > (prog-if 02 [16550])
> >     Subsystem: Unknown device 2205:2004
> >     Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> >     Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR-
> >     Interrupt: pin A routed to IRQ 201
> >     Region 0: Memory at fddfe000 (32-bit, non-prefetchable) [size=4K]
> > ------------------------------------
> >
> >
> > On 2/12/08, Vivek Mangal <vivek.mangal9685 at gmail.com> wrote:
> > >
> > > hello all,
> > > My new PC show a message all time at the booting
> > > i can not under stand what is the problem ?
> > > and how can i recover it ?
> > > problem is that
> > >
> > > PCI: cannot allocate resource region 3 of devices 0000:00:00:0
> > >
> > > if any have any idea then please tell me.
> > >
> >
> >
>



More information about the redhat-list mailing list