any tool to help configure bonding?

[ESGLinux]

Hello,

I don´t know it, all I can say is that I didn´t

The kernel I´m running is

 2.6.18-128.el5

With the default options

ESG

2009/2/26 chloe K <chloekcy2000 at yahoo.ca>

> thank you for your sharing
>
> Do I need to re-compile the kernel to support bonding?
>
> thank you
>
> *ESGLinux <esggrupos at gmail.com>* wrote:
>
> Thanks to all,
>
> Finally with your help I have my test system with bonding configured.
>
> Here is my final configuration for anyone who need it:
>
>
> #more ifcfg-eth0
> DEVICE=eth0
> ONBOOT=yes
> USERCTL=no
> BOOTPROTO=none
> HWADDR=00:0C:29:9D:AE:60
> TYPE=Ethernet
> IPV6INIT=no
> MASTER=bond0
> SLAVE=yes
> USERCTL=no
>
> # more ifcfg-eth1
> DEVICE=eth1
> ONBOOT=yes
> USERCTL=no
> BOOTPROTO=none
> HWADDR=00:0C:29:9D:AE:6A
> TYPE=Ethernet
> IPV6INIT=no
> MASTER=bond0
> SLAVE=yes
> USERCTL=no
>
> #more ifcfg-bond0
> DEVICE=bond0
> IPADDR=192.168.1.193
> NETMASK=255.255.255.0
> NETWORK=192.168.1.0
> NETWORKING_IPV6=no
> GATEWAY=192.168.1.1
> BROADCAST=192.168.1.255
> USERCTL=no
> BOOTPROTO=none
> ONBOOT=yes
> TYPE=Ethernet
>
> #more route-bond0
> GATEWAY0=192.168.1.1
> NETMASK0=255.255.255.0
> ADDRESS0=192.168.1.0
>
>
> #more /etc/modprobe.conf
> alias eth0 pcnet32
> alias scsi_hostadapter ata_piix
> alias eth1 pcnet32
> alias bond0 bonding
> options bond0 mode=4 miimon=100
>
>
> An finally the ifconfig:
>
>
> ifconfig
> bond0 Link encap:Ethernet HWaddr 00:0C:29:9D:AE:60
> inet addr:192.168.1.193 Bcast:192.168.1.255 Mask:255.255.255.0
> inet6 addr: fe80::20c:29ff:fe9d:ae60/64 Scope:Link
> UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
> RX packets:4475 errors:0 dropped:0 overruns:0 frame:0
> TX packets:439 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:320224 (312.7 KiB) TX bytes:56916 (55.5 KiB)
>
> eth0 Link encap:Ethernet HWaddr 00:0C:29:9D:AE:60
> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
> RX packets:2376 errors:0 dropped:0 overruns:0 frame:0
> TX packets:432 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:168785 (164.8 KiB) TX bytes:56334 (55.0 KiB)
> Interrupt:169 Base address:0x1080
>
> eth1 Link encap:Ethernet HWaddr 00:0C:29:9D:AE:60
> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
> RX packets:2103 errors:0 dropped:0 overruns:0 frame:0
> TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:151679 (148.1 KiB) TX bytes:1984 (1.9 KiB)
> Interrupt:177 Base address:0x1400
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:1440 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1440 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:5616724 (5.3 MiB) TX bytes:5616724 (5.3 MiB)
>
> With this configuration ALL works fine. Now Im going to test different
> configurations,
>
> Thanks again
>
> Greetings
>
> ESG
> --
> redhat-list mailing list
> unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/redhat-list
>
>
>    ------------------------------
>
> *Yahoo! Canada Toolbar :* Search from anywhere on the web and bookmark
> your favourite sites. Download it now! <http://ca.toolbar.yahoo.com/>
>