how to setup a RHEV hypervisor using RHEL

[ESGLinux]

Hi Vincent,

I have solved the problem,

I have 2 problems:

- I was running iptables and blocking the ports
- I was running a xen kernel and It seems to be a problem,

I have solved this issues and now I have my RHEL registered in the RHEV-M
and running,

Thank you very much for your help

ESG


2010/10/6 Vincent Van der Kussen <Vincent.VanderKussen at btr-services.be>

> Hi,
>
> try running service vdsmd restart. Do you have iptables...
>
> Regards,
> Vincent
>
>
> Vincent Van der Kussen
> System Engineer
> direct: +32 3 369 01 93
> Vincent.VanderKussen at btr-services.be
>
> BTR Services
> Groene Hofstraat 31
> 2850 Boom
> Belgium
> www.btr-services.be
> tel: +32 3 450 89 80
> fax: +32 3 450 89 89
>
>
>
> - DISCLAIMER -
> This message contains confidential information and is intended only for
> redhat-list at redhat.com. If you are not redhat-list at redhat.com, you should
> not disseminate, distribute or copy this e-mail. Please notify
> Vincent.VanderKussen at btr-services.be immediately by e-mail if you have
> received this e-mail by mistake and delete this e-mail from your system.
> E-mail transmission cannot be guaranteed to be secure or error-free as
> information could be intercepted, corrupted, lost, destroyed, arrive late or
> incomplete, or contain viruses. Vincent Van der Kussen therefore does not
> accept liability for any errors or omissions in the contents of this
> message, which arise as a result of e-mail transmission. If verification is
> required please request a hard-copy version.
> --------------------------------------------------------------------------
>
> ________________________________________
>
> From: redhat-list-bounces at redhat.com [redhat-list-bounces at redhat.com] On
> Behalf Of ESGLinux [esggrupos at gmail.com]
> Sent: Wednesday, October 06, 2010 7:24 PM
> To: General Red Hat Linux discussion list
> Subject: Re: how to setup a RHEV hypervisor using RHEL
>
> Hi,
>
> Thanks for your answer,
>
> I have done what you told and I get the host, but I get an error in the
> /var/log/vdsm/vdsm.log
>
> MainThread::ERROR::2010-10-06 19:20:19,630::ksm::28::vds::failed to find
> kksmd thread
>
> and the host is in status "Non Responsive"
>
> What I have to do now to get the node up???
>
> Thanks again,
>
> ESG
>
>
> 2010/10/6 Vincent Van der Kussen <Vincent.VanderKussen at btr-services.be>
>
> > Hi,
> >
> > Just go to the RHEV Manager and add the host. It needs to be subscribed
> to
> > the right channels.
> > Once added in the RHEV Manager, the host will be automatically installed
> as
> > a hypervisor host.
> >
> > Regards,
> > Vincent
> >
> >
> > Vincent Van der Kussen
> > System Engineer
> > direct: +32 3 369 01 93
> > Vincent.VanderKussen at btr-services.be
> >
> > BTR Services
> > Groene Hofstraat 31
> > 2850 Boom
> > Belgium
> > www.btr-services.be
> > tel: +32 3 450 89 80
> > fax: +32 3 450 89 89
> >
> >
> >
> > - DISCLAIMER -
> > This message contains confidential information and is intended only for
> > redhat-list at redhat.com. If you are not redhat-list at redhat.com, you
> should
> > not disseminate, distribute or copy this e-mail. Please notify
> > Vincent.VanderKussen at btr-services.be immediately by e-mail if you have
> > received this e-mail by mistake and delete this e-mail from your system.
> > E-mail transmission cannot be guaranteed to be secure or error-free as
> > information could be intercepted, corrupted, lost, destroyed, arrive late
> or
> > incomplete, or contain viruses. Vincent Van der Kussen therefore does not
> > accept liability for any errors or omissions in the contents of this
> > message, which arise as a result of e-mail transmission. If verification
> is
> > required please request a hard-copy version.
> >
> --------------------------------------------------------------------------
> >
> > ________________________________________
> >
> > From: redhat-list-bounces at redhat.com [redhat-list-bounces at redhat.com] On
> > Behalf Of ESGLinux [esggrupos at gmail.com]
> > Sent: Wednesday, October 06, 2010 5:53 PM
> > To: General Red Hat Linux discussion list
> > Subject: how to setup a RHEV hypervisor using RHEL
> >
> > Hi all,
> >
> > I´m trying to use a RHEL 5.5 as hypervisor but I can´t get it,.
> >
> > I have followed the
> > doc
> >
> Red_Hat_Enterprise_Virtualization_for_Servers-2.2-Installation_Guide-en-US.pdf
> > but I can´t get the server in the RHEV Manager
> >
> > When I install a standalone hypervisor automatically I get the host
> > registered in the RHEV Manager, but with RHEL I don´t get it and I don´t
> > know how to register it.
> >
> > Anyone know how to do it?
> >
> > Thanks in advance
> >
> > ESG
> > --
> > redhat-list mailing list
> > unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> > https://www.redhat.com/mailman/listinfo/redhat-list
> >
> >
> > --
> > redhat-list mailing list
> > unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> > https://www.redhat.com/mailman/listinfo/redhat-list
> >
> --
> redhat-list mailing list
> unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/redhat-list
>
>
> --
> redhat-list mailing list
> unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/redhat-list
>