slint and transmission-cli questions

[Linux for blind general discussion]

Hello Anonymous;)

I just built and installed transmission, using the SlackBuild from here:
https://slackbuilds.org/repository/14.2/network/transmission/
I ran the script directly but could as well have run as root:
spi -i transmisson
(to get the package built and installed. By default all parts are built, this includes beyond the cli: GTK, Qt and the daemon.)

Then I issued this command:
transmission-cli -w /tmp http://www.slackware.com/torrents/slackware
I get the same errors, however it works

didier[~]$ transmission-cli -w /tmp http://www.slackware.com/torrents/slackware64-14.2-install-dvd.torrent
transmission-cli 2.93 (3c5870d4f5)
[2018-05-03 14:39:36.370] Transmission 2.93 (3c5870d4f5) started
[2018-05-03 14:39:36.371] RPC Server: Adding address to whitelist: 127.0.0.1
[2018-05-03 14:39:36.371] UDP: Failed to set receive buffer: requested 4194304, got 425984
[2018-05-03 14:39:36.371] UDP: Please add the line "net.core.rmem_max = 4194304" to /etc/sysctl.conf
[2018-05-03 14:39:36.371] UDP: Failed to set send buffer: requested 1048576, got 425984
[2018-05-03 14:39:36.371] UDP: Please add the line "net.core.wmem_max = 1048576" to /etc/sysctl.conf
[2018-05-03 14:39:36.371] DHT: Reusing old id
[2018-05-03 14:39:36.372] DHT: Bootstrapping from 44 IPv4 nodes
[2018-05-03 14:39:36.704] Port Forwarding (NAT-PMP): initnatpmp succeeded (0)
[2018-05-03 14:39:36.704] Port Forwarding (NAT-PMP): sendpublicaddressrequest succeeded (2)
[2018-05-03 14:39:37.442] Saved "/home/didier/.config/transmission/torrents/slackware64-14.2-iso.85922fbee6dce5e2.torrent"
[2018-05-03 14:39:38.733] Port Forwarding (UPnP): Found Internet Gateway Device "http://192.168.0.254:5678/control/wan_ip_connection"
[2018-05-03 14:39:38.733] Port Forwarding (UPnP): Local Address is "192.168.0.10"
[2018-05-03 14:39:38.756] Port Forwarding (UPnP): Port forwarding through "http://192.168.0.254:5678/control/wan_ip_connection", service "urn:schemas-upnp-org:service:WANIPConnection:1". (local address: 192.168.0.10:51413)
[2018-05-03 14:39:38.756] Port Forwarding (UPnP): Port forwarding successful!
[2018-05-03 14:39:38.756] Port Forwarding: State changed from "Not forwarded" to "Forwarded"
Progress: 16.7%, dl from 39 of 50 peers[2018-05-03 14:39:56.000] slackware64-14.2-iso: Starting IPv4 DHT announce (poor, 16 nodes)
Progress: 19.8%, dl from 49 of 50 peers (2.08 MB/s), ul to 0 (0 kB/s) [0.00]

So I don't think you should worry about the errors.

I never used transmission before so can't answer your other question, but I am CCing B. Watson, the transmission SlackBuid maintainer, who certainly knows more.

Le 03/05/2018 à 13:44, Linux for blind general discussion a écrit :
> Anyone running transmission-cli on slint?  I get a couple errors when it starts up I think I can turn off by disabling port mapping with the -M option.  Apparently transmission-cli expects to be on systemd machines because both error messages want /etc/sysctl.conf to be updated and have lines added to it.  I don't know what to do for system v systems.  Also, I don't know what port mapping would get me if it were enabled as well as disabled.  Transmission-cli runs after these errors though.
> 
> 
> 
> -- 
> 
> _______________________________________________
> Blinux-list mailing list
> Blinux-list at redhat.com
> https://www.redhat.com/mailman/listinfo/blinux-list
>