How to use kickstart when I have 2 network card

[Zheng, Shaohui]

 We also meet this issue, most of our machine have 2 network card. Your suggestion is very helpful for us. Thanks Shabazian.

 

Shaohui

Best Regards

 

________________________________

From: kickstart-list-bounces at redhat.com [mailto:kickstart-list-bounces at redhat.com] On Behalf Of Shabazian, Chip
Sent: 2007年4月27日 0:39
To: Discussion list about Kickstart
Subject: RE: How to use kickstart when I have 2 network card

 

We kickstart servers with multiple NIC's every day.  One thing you need to be aware of is that RHEL 4 and 5 enumerate the bus differently than RHEL 3, so a NIC that was eth0 in RHEL 3 may no longer be eth0 when building the exact same machine with RHEL 4 or 5.  If the NIC's are on the same bus, then the order doesn't change (such as with the dual embedded NIC's on the HP DL servers), but if they are on different busses (this happens to us when there is another NIC in a PCI slot in addition to the embedded NICs), the order will be different in RHEL 3 than in RHEL 4 or 5.

 

ksdevice=mac_address will resolve this issue for retrieving your kickstart file, but you will need to make sure that you have the right ethX device in your kickstart file.

 

Chip Shabazian
VP ; Sr. Consultant - System Engineering
Bank of America
E&O OS Services -- Linux
e: chip.shabazian at bankofamerica.com
p: 925 692-7000

 

 

________________________________

From: kickstart-list-bounces at redhat.com [mailto:kickstart-list-bounces at redhat.com] On Behalf Of Callahan, Tom
Sent: Thursday, April 26, 2007 6:38 AM
To: Discussion list about Kickstart
Subject: Re: How to use kickstart when I have 2 network card

Use ksdevice=eth(x). Other useful options are:

ip=192.10.10.10 ― statically set ip
netmask=255.255.255.0 ― statically set netmask
dns=10.10.10.10 ― statically set dns
gateway= 10.10.10.10 ― statically set gateway address

This way you don’t even need DHCP to set up a machine :)


On 4/26/07 2:21 AM, "Zheng, Shaohui" <shaohui.zheng at intel.com> wrote:

Hi all
       I meet problems when I use kickstart to do a full automation installation. I try to install the OS from a NFS server, all the ISO files and kickstart configuration files are in network. It works well if we have one network card only, but if some machine have 2 network card, it can not do it automatically. The kickstart manual says that if we have two network card, we must put the kickstart configuration file in local file system. Does it mean we do not have any other solution if we put the configuration file in network? If you know how to do it, would you please tell me, your suggestion is helpful for me, thanks so much.
 
Shaohui
Best Regards



________________________________

_______________________________________________
Kickstart-list mailing list
Kickstart-list at redhat.com
https://www.redhat.com/mailman/listinfo/kickstart-list




-------------------------------
Tom Callahan
TDS Engineering
410-229-1361  Tel
410-588-7605  Mobile 
410-229-1512  Fax 
callahant at TESSCO.com

TESSCO
Your Total Source for Wireless
http://www.tessco.com

Network Infrastructure Equipment | Mobile Devices & Accessories | Installation, Test, Equipment & Supplies

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/kickstart-list/attachments/20070427/04ab1edd/attachment.htm>